Civil Engineering MCQs: 3,057 practice questions with answer choices and available explanations. Page 154 of 204.

Civil Engineering MCQs by topic

Surveying100 Structural Analysis53 Fluid Mechanics98 Highway Engineering129 Environmental Engineering146

Now you can submit the latest Civil Engineering MCQs MCQs from your test! SUBMIT HERE

Civil Engineering MCQs

Showing page 154 of 204 · 3,057 total solved questions available.

Study Topic

⚡Start Quiz Mode to Practice Like the Real Exam!

The portal bracing in a truss bridge is used to________?

A.prevent the sidesway buckling of top chord

B.keep the rectangular shape of the bridge cross-section

C.stiffen the structure laterally

D.transfer load from top of end posts to bearings

Explanation: The correct answer is transfer load from top of end posts to bearings.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

Increase in the moisture content in concrete________?

A.reduces the strength

B.does not change the strength

C.increases the strength

D.all of the above

Explanation: The correct answer is reduces the strength.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

Pick up the correct statement from the following ________?

A.The materials separated by screens, is called screenings

B.The process of burning the screenings, is known as compositing

C.The screenings are disposed off either by burning or by burial or by dumping

D.All the above

Explanation: The correct answer is All the above.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

Allowable bearing pressure for a foundation depends upon________?

A.allowable settlement only

B.none of above

C.both allowable settlement and ultimate bearing capacity

D.ultimate bearing capacity of soil only

Explanation: The correct answer is both allowable settlement and ultimate bearing capacity.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

For a Broad Gauge route with M+7 sleeper density, number of sleepers per rail length is________?

A.19

B.20

C.21

D.18

Explanation: The correct answer is 20.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

In Intrumental landing system, the middle markers are located________?

A.about 7 km. ahead of the runway threshold

B.at the runway threshold

C.along the extended centre line of runway end

D.about 1 km. ahead of the runway threshold

Explanation: The correct answer is about 1 km. ahead of the runway threshold.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

What refers to the market situation in which any given product is supplied by a very large number of vendors and there is no restriction against additional vendors from entering the market?

A.Oligopoly

B.Oligopsony

C.Monopoly

D.Perfect competition

Explanation: The correct answer is Perfect competition.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

Transit rule of adjusting the consecutive coordinates of a traverse is used where________?

A.linear and angular measurements of the traverse are of equal accuracy

B.all of the above

C.linear measurements are more accurate than angular measurements

D.angular measurements are more accurate than linear measurements

Explanation: The correct answer is angular measurements are more accurate than linear measurements.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

A part of the slab may be considered as the flange of the T-beam if________?

A.It is built integrally with the beam

B.Flange has adequate reinforcement transverse to beam

C.All the above

D.It is effectively bonded together with the beam

Explanation: The correct answer is All the above.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

The relation between probability (P) and recurrence interval (T) is given by________?

A.PT2 = 1

B.P/T = 1

C.PT = 1

D.P/T2 = 1

Explanation: The correct answer is PT = 1.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

The particular places where pedestrians are to cross the pavement are properly marked by the pavement marking known as________?

A.crosswalk lines

B.stop lines

C.turn markings

D.lane lines

Explanation: The correct answer is crosswalk lines.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

If the velocity is zero over half of the cross-sectional area and is uniform over the remaining half, then the momentum correction factor is________?

A.1

B.4

C.2

D.4/3

Explanation: The correct answer is 2.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

For determining the support reactions at A and B of a three hinged arch, points B and Care joined and produced to intersect the load line at D and a line parallel to the load line through A at D’. Distances AD, DD’ and AD’ when measured were 4 cm, 3 cm and 5 cm respectively. The angle between the reactions at A and B is________?

A.45°

B.90°

C.60°

D.30°

Explanation: The correct answer is 90°.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

The arrangement of terrain features which provides attributes: the shape, size and texture of objects, is called________?

A.Temporal variation

B.None of these

C.Spectral variation

D.Spatial variation

Explanation: The correct answer is Spatial variation.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

True one-dimensional flow occurs when________?

A.the direction and magnitude of the veiocity at all points are identical

B.the fluid particles move in plane or parallel planes and the streamline pat-terns are identical in each plane

C.the velocity of successive fluid par-ticles, at any point, is the same at suc-cessive periods of time

D.the magnitude and direction of the velocity do not change from point to point in the fluid

E.velocity, depth, pressure etc. change from point to point in the fluid flow

Explanation: The correct answer is the direction and magnitude of the veiocity at all points are identical.

Submitted by: Academy of Pakistan

Read More Details about this Mcq →

Continue studying

Practice quiz Past papers Chemical Engineering MCQs Electrical Engineering MCQs Mechanical Engineering MCQs Software Engineering MCQs